Search Results

The structure-, fluid- and air-borne excitation generated by HVAC compressors can lead to annoying noise and low frequency vibrations in the passenger compartment. These noises and vibrations are of great interest in order to maintain high passenger comfort of EV vehicles. The main objective of this paper is to develop a numerical model of the HVAC system and to simulate the structure-borne sound transmission from the compressor through the HVAC hoses to the vehicle in a frequency range up to 1 kHz. An existing automotive HVAC system was fully replicated in the laboratory. Vibration levels were measured on the compressor and on the car body side of the hoses under different operational conditions. Additional measurements were carried out using external excitation of the compressor in order to distinguish between structure- and fluid-borne transmission. The hoses were experimentally characterised with regard to their structure-borne sound transmission characteristics.

In response to a growing need for a practical and technically valid method for measuring exhaust sound pressure levels (SPL) of on-highway motorcycles, the SAE Motorcycle Technical Steering Committee has developed Surface Vehicle Recommended Practice J28251, “Measurement of Exhaust Sound Pressure Levels of Stationary On-Highway Motorcycles,” which includes a new stationary sound test procedure and recommendations for limit values. Key goals of the development process included: minimal equipment requirements, ease of implementation by non-technical personnel, and consistency with the federal EPA requirements; in particular, vehicles compliant with the EPA requirements should not fail when assessed using J2825. Development of the recommended practice involved a comprehensive field study of 25 motorcycles and 76 different exhaust systems, ranging from relatively quiet OEM systems to unbaffled, aftermarket exhaust systems.

The passive pre-chamber (PC) is valued for its jet ignition (JI) and is suitable for wide use in the field of gasoline direct injection (GDI) for small passenger cars, which can improve the performance of lean combustion. However, the intake, exhaust, and ignition combustion stability of the engine at low speed is a shortcoming that has not been overcome. Changing the structural design to increase the fluidity of the main chamber (MC) and pre-chamber (PC) may reduce jet ignition performance, affecting engine dynamics. This investigation is based on non-uniformly nozzles distributed passive pre-chamber, which is adjusted according to the working medium exchange between PC and MC. The advantages and disadvantages of the ignition mode of PC and SI in the target engine speed range are compared through optical experiments on a small single-cylinder GDI engine.

The thermal degradation of ion E/R (ion exchange resin) has been investigated in the pure water generation power plants, but not in electric power generation in Fuel Cell Vehicle (FC-V). Electric power generation fuel cell uses its coolant water of 50wt% ethylene glycol (EG). When EG degraded in the heated condition, ions elute in the coolant. This ion elution reduces the ion E/R performance through reduction of its capacity. This paper describes the effect of thermal degradation of ion E/R in FC-V.

As the carbon neutrality to reduce greenhouse gas emissions has become a global movement, the development of power sources using carbon-free fuels is an essential task for the industry. Accordingly, many companies in various fields that need carbon reduction are striving to develop power sources and build energy value chains using carbon-free or carbon-neutral fuels such as hydrogen and E-fuel. Ammonia, which is also a carbon-free fuel, stands as an efficient energy vector delivering high energy density and flexibility in transportation and storage, capable of mitigating hydrogen’s key drawbacks. However, difficulty of controlling combustion of ammonia due to its fuel characteristics limited the development of internal combustion engines using ammonia to the basic research stage in the limited operating conditions. Hyundai Motor Company presents the development of ammonia fueled 4-cylinder SI engine using direct injection strategy, designed based on 2.5L LPG T-DI engine.

To properly compare and contrast the environmental performance of one vehicle technology against another, it is necessary to consider their production, operation, and end-of-life fates. Since 1995, Argonne’s GREET® life cycle analysis model (Greenhouse gases, Regulated Emissions, and Energy use in Technologies) has been annually updated to model and refine the latest developments in fuels and materials production, as well as vehicle operational and composition characteristics. Updated cradle-to-grave life cycle analysis results from the model’s latest release are described for a wide variety of fuel and powertrain options for U.S. light-duty and medium/heavy-duty vehicles. Light-duty vehicles include a passenger car, sports utility vehicle (SUV), and pick-up truck, while medium/heavy-duty vehicles include a Class 6 pickup-and-delivery truck, Class 8 day-cab (regional) truck, and Class 8 sleeper-cab (long-haul) truck.

Lubrication systems play a major role not only in the durability of modern IC engines but also in performance and emissions. The design of the lubrication system influences the brake thermal efficiency of the engine. Also, efficient lubrication reduces the engine's CO2 emissions significantly. Thus, it is critical for an IC engine to have a well-designed lubrication system that performs efficiently at all engine operating conditions. The conventional lubrication system has a fixed-displacement oil pump that can cater to a particular speed range. However, a fully variable displacement oil pump can cater to a wide range of speeds, thereby enhancing the engine fuel efficiency as the oil flow rates can be controlled precisely based on the engine speed and load conditions. This paper primarily discusses the optimization of a lubrication system with a Variable Displacement Oil Pump (VDOP) and a map-controlled Piston Cooling Jet (PCJ) for a passenger car diesel engine.

Internal combustion engine (IC engine) vehicles are commonly used for transportation due to their versatility. Due to this, efficiency in design process of IC engines is critical for the industry. To assess performance capabilities of an IC engine, thermal predictions are of utmost consequence. This study describes a computational method based on unsteady Reynolds-averaged Navier–Stokes equations that resolves the gas–liquid interface to examine the unsteady single phase/multiphase flow and heat transfer in a 4-cylinder Inline (i-4) engine. The study considers all important parts of the engine i.e., pistons, cylinder liners, head, block etc. The study highlights the ease of capturing complex and intricate flow paths with a robust mesh generation tool in combination with a robust high-fidelity interface capturing VOF (Volume-of-Fluid) scheme to resolve the gas-liquid interfaces.

Ensuring spray robustness of gasoline direct injection (GDI) is essential to comply with stringent future emission regulations for hybrid and internal combustion engine vehicles. This study presents experimental and numerical assessments of spray for lateral-mounted GDI sprays with two different plume arrangements to analyze spray collapse characteristics, which can significantly deteriorate the atomization performance of fuel sprays. Novel spray characterization methods are applied to analyze complex spray collapse behaviors using diffusive back-illuminated extinction imaging (DBIEI) and 3D computed tomographic (CT) image reconstruction. A series of computational fluid dynamics (CFD) simulations are performed to analyze the detailed spray characteristics besides experimental characterization. Spatio-temporal plume dynamics of conventional triangle-pattern spray are evaluated and compared to a plume pattern with an inversed T pattern that has more open space between plumes.

This study focuses on evaluation of various fuels within a conventional gasoline internal combustion engine (ICE) vehicle and the implementation of advanced emissions reduction technology. It shows the robustness of the implemented technology packages for achieving ultra-low tailpipe emissions to different market fuels and demonstrates the potential of future GHG neutral powertrains enabled by drop-in lower carbon fuels (LCF). An ultra-low emission (ULE) sedan vehicle was set up using state-of-the-art engine technology, with advanced vehicle control and exhaust gas aftertreatment system including a prototype rapid catalyst heating (RCH) unit. Currently regulated criteria pollutant emission species were measured at both engine-out and tailpipe locations. Vehicle was run on three different drive cycles at the chassis dynamometer: two standard cycles (WLTC and TfL) at 20°C, and a real driving emission (RDE) cycle at -7°C.

As a novel ignition technology, pre-chamber ignition can enhance ignition energy, promote flame propagation, and augment turbulence. However, this technology undoubtedly faces challenges, particularly in the context of emission regulations. Of this study, the transient characteristics of combustion and emissions in a hybrid electric vehicle (HEV) gasoline engine with active pre-chamber ignition (PCI) under the first combustion cycle of quick start are focused. The results demonstrate that the PCI engine is available on the first cycle for lean combustion, such as lambda 1.6 to 2.0, and exhibit particle number (PN) below 7×107 N/mL at the first cycle. These particles are predominantly composed of nucleation mode (NM, <50 nm) particles, with minimal accumulation mode (AM, >50 nm) particles.

Designing for fatigue performance requires extensive knowledge of material properties, component geometry and dynamic loading conditions. These topics are addressed in an ongoing cohesive research program on fatigue behavior of magnesium die castings. The current phase of the program includes effects of alloy type, mean stress level, surface condition, and level of tensile properties. The results, presented as S-N curves and Goodman diagrams, show a significant difference in the fatigue life between AZ91D and the AM alloys. Fatigue behavior of AM60B was strongly dependent on the mean stress level, but was not significantly influenced by a minor difference in casting quality. The fatigue behavior of AM50A was not noticeably changed by the addition of vibratory polishing.

Volvo has developed the first production emission control system to fully utilize a three-way catalyst. Called the “Volvo Lambda-sond system”, it is applied to the 4-cylinder in-line B21 engine, and employs three essential new components - an exhaust gas composition sensor, an additional feed-back loop to the continuous fuel injection system, and the catalyst. Outstanding certification results were achieved, especially for NOx, combined with good driveability, power output, and fuel economy. The development and performance of the system, and the test procedures used, are described in detail, and its future potential and limitations are discussed.

The deionized water/ethylene glycol coolant used in the Ford Focus Fuel Cell Vehicle (FCV) requires very low conductivity (< 5 μS/cm) to avoid current leakage and short circuiting, presenting a unique water chemistry issue. The coolant's initially low conductivity increases as: 1) ions are released from system materials through leaching, degradation and/or corrosion, and 2) organic acids are produced by ethylene glycol degradation. Estimating the leaching potential of these ions is necessary for design and operation of fuel cell vehicles. An on-board mixed-bed, ion exchange resin filter is used to maintain low conductivity by removing leached or produced ions. Various candidate materials were evaluated for leaching potential by exposing them to coolant at the design operating temperature for several months and periodically analyzing the coolant for ions.

The importance of fuel costs provide a strong incentive to operate the SST on existing jet fuels. Potential fuel system problems peculiar to the supersonic transport such as fuel boiling, spontaneous ignition, deposit formation, lubricity, and combustion characteristics are reviewed. The significance of these problems is established. Their severity depends on the particular environment provided by the designer. The difficulties of defining fuel properties to eliminate these problems are covered. The paper shows that major steps have been taken to operate the SST on current quality jet fuels but all necessary fuel quality control tests are not yet available.

The objective of this experimental investigation was to analyze the effect of various exhaust gas aftertreatment technologies on particulate number emissions (PN) of an MPFI EU5 motorcycle. Specifically, three different aftertreatment strategies were compared, including a three-way-catalyst (TWC) with LS structure as the baseline, a hybrid catalyst with a wire mesh filter, and an optimized gasoline particulate filter (GPF) with three-way catalytic coating. Experimental investigations using the standard test cycle WMTC performed on a two-wheeler chassis dynamometer, while the inhouse particulate sampling system was utilized to gather information about size-dependent filtering efficiency, storage, and combustion of nanoparticles. The particulate sampling and measuring system consist of three condensation particle counters (CPCs) calibrated to three different size classes (SPN4, SPN10, SPN23).

15-5PH is a precipitation-hardening, martensitic stainless steel used for primary structural elements such as engine mounts where corrosion resistance, high strength, good fatigue and fracture toughness is required. The material composition is defined in AMS5659M. This alloy can be either Type 1 - vacuum arc remelt (VAR) or Type 2 - electro slag remelt (ESR) and is most commonly heat treated per SAE AMS-H-6875 or AMS2759/3 to condition H1025 (an ultimate tensile strength of 155 ksi [1070 MPa] minimum). Typically material handbooks have limited fatigue data and most data is only for Type 1. Therefore, the fatigue properties of 15-5PH H1025 stainless steel for both Type 1 and Type 2 were determined. The objective of the fatigue testing was to generate a family of S-N curves (maximum stress versus number of cycles to failure) for a series of stress ratios across the entire range of cycles to failure.

The novel wave-shaped bowl piston geometry design with protrusions has been proved in previous studies to enhance late-cycle mixing and therefore significantly reduce soot emissions and increase engine thermodynamic efficiency. The wave-shaped piston is characterized by the introduction of evenly spaced protrusions around the inner wall of the bowl, with a matching number with the number of injection holes, i.e., flames. The interactions between adjacent flames strongly affect the in-cylinder flow and the wave shape is designed to guide the near-wall flow. The flow re-circulation produces a radial mixing zone (RMZ) that extends towards the center of the piston bowl, where unused air is available for oxidation promotion. The waves enhance the flow re-circulation and thus increase the mixing intensity of the RMZ.